Furuno DRS4D Manual do Utilizador

www.furuno.co.jpInstallation ManualRADAR SENSORDRS2D/DRS4D/DRS4A/DRS6A/DRS12A/DRS25ASAFETY INSTRUCTIONS ...

45. Coat the hex bolts (4 pcs.) with silicone sealant. Fasten the antenna radiator to the radiator bracket with the hex bolts, flat washers and spring

52. Lay the radar sensor on the mounting platform, orienting it as shown below. (The hinges must face toward the stern.)3. Insert four hex bolts (M12

64. Pass flat washers (M12, supplied), spring washers (M12, supplied) and nuts (M12, supplied) onto hex. bolts. Fasten by tightening nuts. Do not fast

7Using inside fixing holes of the sensor housingIf this radar is replacing a FURUNO radar whose mounting dimensions are the same as this one (140 x 15

81.4 Mounting of Power Supply Unit PSU-013 (for DRS25A)/PSU-012 (Option)For combinations shown below, the optional power supply unit PSU-012 (Code No.

92. WIRINGThe MFDBB, MFD8, MFD12 or PSU-012 connects to the radar sensor with the two-way cable MOD-ASW0001 (MOD-ASW0002 for DRS25A).In order to minim

10Wiring for DRS2D/4D/4A/6A/12A with PSU-012Wiring for DRS25ARadar SensorDRS4A/DRS6A/DRS12ANMEA2000Equipment: Standard Supply: Optional Supply: Local

11How to terminate of NMEA2000 connectionWhen connecting the radar sensor and an NMEA2000 equipment using the optional cable M12-05BFFM (φ6) or CB-05B

122.1 Wiring inside DRS2D/4DTwo-way cable connection1. Unfasten three screws at the bottom of the mounting base to remove the fixing plate for the gas

136. Slide the gasket on cables so that the amount of cable above the gasket is lower than the RF chassis.Note: If the two-way cable touches the platf

iWARNINGWARNINGWear a safety belt and hard hat whenworking on the antenna unit.Serious injury or death can result ifsomeone falls from the radar mast.

143. Insert wires of cable M12-05BFFM (φ6) or CB-05BFFM (φ10) to the NMEA connector inside the radar sensor, consulting the label on the connector for

154. Push LAN and POWER cables of the two-way cable and cable M12-05BFFM (φ6) or CB-05BFFM (φ10) into the slits of the gasket inside the mounting base

162.2 Wiring inside DRS4A/6A/12A/25ATwo-way cable connectionIf you have no NMEA2000 equipment to connect, use the MOD-ASW0001 cable (standard sup-ply)

175. Attach the LAN cable of the two-way cable to the LAN terminal in the radar sensor.DRS4A/6A/12ADRS25A6. Refer to the illustration shown below, and

187. Slide the gasket on cables so that the amount of cable above the gasket is lower than the RF chassis.8. Push the gasket and washers into the hole

19the crimp-on lug (pre-attached at the bottom of the chassis) to the drain wire, and fasten it with the screw shown below.5. Depending on the NMEA200

202.3 Wiring of Power Supply Unit PSU-013 (for DRS25A)1. Detach the body cover by hand.2. Loosen six pan head screws (M3x8) and slide the shield cover

212.4 Wiring inside Power Supply Unit PSU-012 (Option)1. Detach the body cover by hand.2. Loosen six pan head screws (M3x8) and slide the shield cover

%1&'016;2'%2⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..

%1&'016;2'⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..#6+10/#6'4+#.5Ꮏ੐᧚ᢱ

iiSYSTEM CONFIGURATIONDRS2D/4D/4A/6A/12ARADAR SENSORDRS4A/DRS6A/DRS12AORRECTIFIERRU-1746B100/110/220/230 VAC12-24 VDCNMEA 2000Equipment: Standard Sup

%1&'016;2'⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..#6+10/#6'4+#.5Ꮏ੐᧚ᢱ

21/Aug/09 R.EsumiD-1

22/Mar/08 R.EsumiD-2

Jan.18'08 R.EsumiD-3

2/Apr/08 R.EsumiD-4

Oct.15'07 R.EsumiD-5

243A1BCDRAWNCHECKEDAPPROVEDDWG.No.TITLENAME名称INTERCONNECTION DIAGRAM相互結線図REF.No.SCALE MASSkgレーダーセンサーRADAR SENSORT.YAMASAKIDRS2D/4DT.TAKENONOTE1. SHIPY

243A1BCDRAWNCHECKEDAPPROVEDDWG.No.TITLENAME名称INTERCONNECTION DIAGRAM相互結線図REF.No.SCALE MASSkgレーダーセンサーRADAR SENSORT.YAMASAKIT.TAKENODRS4A/6ANOTE1. SHIPY

243A1BC12456378NCNCE_TD-PNCE_TD-NE_RD-PNCE_RD-NRJ45 J2*3シロ WHTクロ BLK12456378NCNCE_TD-PNCE_TD-NE_RD-PNCE_RD-NRJ45J3PSU-012POWER SUPPLY UNITパワーサプライユニット1

243A1BC12456378NCNCE_TD-PE_TD-NE_RD-PE_RD-NRJ45J312456378NCNCE_TD-PNCE_TD-NE_RD-PNCE_RD-NB2アカクロREDBLKシロアオWHTBLU12453NET-SNET-LNET-HNET-CSHIELDNMEA2000

iiiDRS25ARADAR SENSORDRS25AORRECTIFIERRU-1746B100/110/220/230 VAC12-24 VDCNMEA 2000Equipment: Standard Supply: Optional Supply: Local SupplyMulti Fun

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

ivEQUIPMENT LISTSStandard supplyName Type Code No. Qty RemarksRadar Sensor XN10A-RSB-118-092 - 1 For DRS4A, w/CP03-32601XN12A-RSB-118-093 1 For DRS6A,

vOptional supplyName Type Code No. Qty RemarksPower Supply UnitPSU-012 - 1 setGasket OP03-203 001-025-290 1For DRS2D/4D, φ10 NMEA2000 cableOP03-205 00

11. MOUNTING1.1 Mounting Considerations• The radar sensor is generally installed either on top of the wheelhouse or on the radar mast on a suitable pl

2For DRS2D/4D1.2 Mounting Procedure for DRS2D/4D1. Remove mounting hardware at the bottom of the radar sensor, four each of hex bolts (M10x20), spring

33. Use the hex bolts*, flat washers and spring washers removed at step 1, and fasten the radome base to the platform. The torque should be between 19